Loading... Please wait...

Sort by:

Accessories

course-dust-filter.gifThe PF40 ‒ Coarse Dust Filter

For environments with elevated levels of coarse dust, the PF40 kit can be added to any IQAir system for superior coarse dust filtration. This helps to extend the life of the unit's standard pre-filter element.

Installation

The PF40 kit consists of an upper grille which screws into the filtration device's base. A synthetic coarse dust filter pad is held in place by a lower grille that is secured by four clips. The 12.7mm (0.5") deep non-woven design of the PF40 filter pad ensures superior coarse dust holding capacity.

IQAir Compatibility

Compatible with all IQAir room air purifiers. Not compatible with the accessories FlexVac, VM FlexVac, VM InFlow and InFlow W125.

Download PF40 Brochure

 

The InFlow (W125)             

The InFlow W125 ducting kit enables any IQAir room air purifier to draw air through a wall or window vent into a room. Use of the InFlow W125 is advisable when the main pollution source is located in adjacent indoor environments or outdoors.

iqair-filter-system.jpgThe InFlow W125 can improve indoor air quality by:

  • Reducing influx of outside pollutants with a build-up of positive pressure
  • Diluting polluted air with clean air
  • Flushing out air pollutants

Enjoy controlled clean air ventilation

An IQAir filter system combined with an InFlow W125 can be installed to draw outdoor air into an indoor environment. In this setup, an IQAir serves as a ventilation system, bringing in oxygen-rich outdoor air and a filtration system, which removes undesirable outdoor pollutants such as pollen, mould spores, dust and exhaust soot. As a result, fresh and filtered outside air is supplied to the room.

Create clean positive pressure areas

An IQAir filter system used in combination with the InFlow W125 will in most cases allow the creation of a positive pressure. This positive pressure helps to reduce contamination in the room by constantly flushing out air pollutants and by preventing outside pollutants from entering the room.

Application Examples

  • Protection of allergy sufferers from pollen exposure in their home
  • Protection from infectious microorganisms (e.g. aspergillus, MRSA) in a hospital
  • Creation of clean research or manufacturing areas (controlled environments)
  • Protection of computer and server rooms from dust and corrosive contaminants
  • Creation of a clean zone within a home or office

Compatibility

Compatible with all IQAir room air cleaners. Not compatible with the accessories PF40, VMF, VM FlexVac, VM InFlow and FlexVac.

iqair.jpgInstallation

The InFlow W125 kit can be easily added to any IQAir room air purifier in a matter of minutes. The only building modification required is a 125mm (5") hole in a window, wall or door which allows you to connect the InFlow W125 fabric duct and draw air into the room.

The duct may be freely flexed to allow control over the desired vent location. It is expandable in length, from 250mm (10") in its original compressed state, to 1000mm (39") when fully extended.

Download Inflow W125 Brochure

 

 

iqair-filter-systems.jpgThe OutFlow (W125)

The OutFlow W125 kit allows filtered air from any IQAir filtration device to be directed through a wall or window vent. The OutFlow W125 kit can be used to:

  • Create clean areas
  • Deliver filtered air into cleanrooms or to the outside
  • Create negative pressure areas
  • Create positive pressure areas

Clean Area and Cleanroom Use

The supply of filtered air into an indoor environment helps reduce air pollution in that room by dilution and the creation of positive pressure, which reduces the infiltration of polluted air from outside the room. With the OutFlow W125 kit, the IQAir system is positioned outside the clean area or cleanroom, saving valuable space and reducing noise exposure. It also eliminates the danger of housing leakage, making it suitable even for certified cleanrooms.

Create clean positive pressure areas

An IQAir filter system used in combination with the InFlow W125 will in most cases allow the creation of a positive pressure in the room into which the air is directed. This positive pressure helps to clean the air in a room by constantly flushing out air pollutants and by preventing outside pollutants from entering the room.

Creation of Pressure Differentials

The OutFlow W125 lets you create pressure differentials between different indoor areas. Negative pressure serves to contain pollutants in an isolation area. Positive pressure protects a clean environment from uncontrolled infiltration of airborne contaminants from polluted areas.

Isolation Areas

Infection control (e.g. tuberculosis, SARS) in hospitals and similar facilities demands the creation of negative pressure environments to reduce the spread of airborne microorganisms. The OutFlow W125 permits operation of the filter unit from within the isolation area, eliminating the danger of housing leakage into the surrounding area.

Emission Control

Legislation limits the emission of polluted air to the outdoors. With the OutFlow W125 the IQAir filtration device can be adapted for emission control. Air is filtered and expelled outdoors via a flexible ducting system. The negative pressure area that is created prevents unfiltered room air from leaking outdoors or to adjacent areas.  

IQAir Compatibility

Compatible with all IQAir room air purifiers and accessories.

Installation

The OutFlow W125 kit easily modifies any IQAir room air purifier. Simply replace the top module of any standard IQAir filtration unit with the TopFlow adapter. All that is needed to install the ducting, wall tube and vent is a 132mm (5.2") opening in a wall or window. The OutFlow W125 kit also includes a damper and a protective mesh grille which prevents backdrafts and entry of coarse particles when the system is not in use. The large 125mm (5") diameter of the ducting ensures low air resistance.

The fabric duct may be freely flexed to allow control over the desired vent location. It is expandable in length from 250mm (10") in its original compressed state to 1000mm (39") when fully extended.

Download OutFlow W125 Brochure

The FlexVac Mobile 

The FlexVac kit converts any IQAir filtration unit into a mobile self-contained extraction system that allows the capture of gases, fumes, smoke, vapours, odours, dust particles and microorganisms directly at their source. Professions and industries that will benefit from healthier working conditions Flexvac offer.

Healthcare Industry

Dentists - Mercury vapours
Laser surgery
Acupuncture
Disinfectant control

Plastics Industry

Plastic welding
Injection moulding
Glueing
Laser cutting

Beauty & Grooming

Nails salons

 Laboratories

Chemical compound control

Chemical and Pharmaceutical Industry

Chemical compound control
Powder dust control

Printing workshops

Solvent Control
Dust Control

Computer and Electronic Industry

Hand soldering
Wave soldering
Dedrossing

 

Exceptional Reachflexvac-mobile.jpg

The FlexVac kit features a self-supporting suction duct that gives the FlexVac a horizontal reach of up to 1.2 m a vertical reach of up to 1.93 m .

Exceptional Maneuverability

The mobility of the FlexVac kit is ensured by six easy-roll casters.

Exceptional Flexibility and Stability

The FlexVac suction duct is made of interlocked polypropylene plastic. This makes the duct stiff enough to be self-supporting and flexible enough to allow for convenient positioning. The 125 mm diameter suction duct can be bent, twisted and turned into virtually any position and will remain in place.

Exceptional Suction Power

The FlexVac kit has exceptional direct source capture power for a system of its size and reach. At a typical air flow of 250 m³/h the air velocity in the suction duct is approx.19 kph.

Exceptional Durability

The suction duct is made of shatterproof and chemically resistant poly-propylene. It has flame retardant characteristics, resists abrasion and withstands temperatures from −25 to 82°C. The support column and base platform are made of powder coated steel.

Ease of Use

Due to its self-contained design the IQAir extraction system requires no venting or ducting to the outside. This makes the system completely mobile, saves energy and expensive building conversion work. Assembly of the FlexVac kit takes just a few minutes and all required tools are supplied.

Easy Maintenance

Dust deposits inside the suction duct and the internal ducting are minimal. The FlexVac kit is easily dismantled for cleaning.

IQAir Compatibility

Compatible with all IQAir filtration devices. Not compatible with the accessories PF40, VMF, VM FlexVac and VM InFlow. 

Download FlexVac Brochure

wall-mounting.jpgThe VMF Wall Mounting                            

The VMF allows you to mount an IQAir filtration system on virtually any structurally sound vertical surface. The VMF is compatible with all IQAir models and is designed to compliment the elegant IQAir look.

Features and Benefits

The vertical mounting of an IQAir unit may be desirable in areas where floor space is scarce or the unit would present an obstacle on the floor. The vertical mount may also improve the air cleaning performance for air pollutants with a rising flow pattern, such as tobacco smoke. If directly mounted above an air pollution source, the IQAir filtration device helps to capture rising dust, fumes or vapours.

Applications

  • Prevent tampering with IQAir systems in public places
  • Improve tobacco smoke filtration in bars and restaurants
  • Filter solvents over a workbench

Servicing & Maintenance

The VMF kit allows all filters to be replaced while the IQAir filtration device remains wall mounted. The removable bottom grille allows easy filter replacement even when the PF40 coarse dust pre-filter accessory is used.

Installation

The VMF kit includes six universal wall plugs and screws suitable for concrete, brick or dry wall. Two wing nuts ensure that the air filtration unit remains safely fixed in the wall mount. The power cord is connectable to the air cleaning unit on either side of the vertical mount. The remote control, which is supplied with each IQAir filtration unit, ensures convenient operability even when the control panel is out of reach.

IQAir Compatibility

Compatible with all IQAir filtration devices. Not compatible with the accessories FlexVac, InFlow W125, VM FlexVac, VM InFlow and Mobility 56.